Quality Remanufactured
Throughly Cleaned & Reconditioned Like New
Each Component Is Carefully Inspected & Replaced If Not Within OEM Tolerances
All Seals & O-Rings Are Replaced With OE Equivalent Parts
Each Unit Is…
This is the stud and bolt kit for Saginaw power steering pumps. Includes (2) studs (3/8"-16 thread), (1) bolt 3/8"-16 thread). Fits most Saginaw pumps through 1977 including Saginaw P series. This set is unplated for use with painted…
Remanufactured Power Steering Pumps are built to meet or exceed OEM performance. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the…
This power steering reservoir cap is a direct replacement for a cracked, worn or missing original equipment cap. Replacing the cap on your Corvette’s power steering reservoir helps to prevent fluid leaks and steering system…
The power-steering pump pressurizes the hydraulic fluid that helps the driver turn the steering wheel. When the pump fails altogether, you'll have zero steering assist making it an important part of any vehicle with a power steering…
Pulley is 5 23/32 O.D.
Reconditioned Item
This 1975-1982 Corvette power steering pump pulley is 5 23/32 OD with 1 Belt Groove. Stamped Steel and is a Press Fit to the pump, No Keyway.
…
Buy The Kit And Save Money ! $ ! The Kit Includes: High Pressure Hose, Low Pressure Return Hose And Clamps Correct Fittings And Line Bends Correct GM Style Rubber Hose Fits All V8 Engines 1967-1968 Camaro power steering systems take…
Power Steering Pump Pulley Woodruff Key
Measurements are 1/8" x 1/2"
Woodruff keys are semicircular shaped, such that, when installed, leave a protruding tab. The keyway in the shaft is a semi-circular pocket, the mating…
High Quality Reproduction Correct, Thin Crush Nut Black Oxide Coating It's the details that win the points at car shows. But, you need the correct items to actually do the job they were supposed to do in the first place rather than a part…
Reproduction Of Original
Replaces GM# 3770509
5 1/2" OD
Fits 1963-68 327ci
Fits 1969-74 350ci With Air Conditioining
Power steering pump pulley, stamped steel. Use on pump w/tapered pulley shaft and lock nut. 5 1/2"…
Quality Reproduction Cradle Bracket Pump To Exhaust Manifold Rear Brace Fits All Small Blocks With Short Water Pump And 8 Harmonic Balancer Bracket Mounting Hardware Set Available As Our Part # PSP-41 Quality reproduction of the 1967-8…
An effective power steering system on a classic Chevrolet Chevelle is appreciated by owners as they negotiate their combination of high horsepower and the large, heavy weight of the vehicle. To replace a cracked or missing original cap on…
Nice reproduction, made in the USA single groove power steering pump pulley. 67-68 350, 69 all engines without air conditioning, 69 396/375. Stamped steel. (Photo shows similar PSP-105)
…
Professionally remanufactured pump assemblies with correct reservoir. Inlet and outlets in correct positions. No core charge required. Pulleys available under Engine -> Engine Pulleys. PSP-30 Shown
…
Reproduction Of Original This Chevelle reproduction power steering bracket has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and function will work…
Direct-fit replacement installs on the power steering pump as part of the engine's accesory drive
Factory-correct reproduction restores original appearance and functionality, or adds it if converting from manual steering
…
OER® reproduction small block power steering adjustor bracket for 1965-68 GM models. Manufactured in stamped steel by OER®, this bracket was original equipment for a variety of Chevrolet and General Motors vehicles and replaces GM…
Quality Reproduction Billet Steel Fits All Cars With Power Steering Made In USA Sold Each Many power steering pump rebuilders do not include this fitting in the back of their pumps and it leaves you trying to plumb female to female…